|
|
Liebermann, D. G., Berman, S., Weiss, P. L. T., & Levin, M. F. (2012). Kinematics of reaching movements in a 2-d virtual environment in adults with and without stroke. IEEE Trans Neural Syst Rehabil Eng, 20(6), 778–787.
Abstract: Virtual reality environments are increasingly being used for upper limb rehabilitation in poststroke patients. Our goal was to determine if arm reaching movements made in a 2-D video-capture virtual reality environment are similar to those made in a comparable physical environment. We compared arm and trunk kinematics for reaches made with the right, dominant arm to three targets (14 trials per target) in both environments by 16 adults with right poststroke hemiparesis and by eight healthy age-matched controls. Movement kinematics were recorded with a three-camera optoelectronic system at 100 samples/s. Reaching movements made by both control and stroke subjects were affected by viewing the targets in the video-capture 2-D virtual environment. Movements were slower, shorter, less straight, less accurate and involved smaller ranges of shoulder and elbow joint excursions for target reaches in the virtual environment compared to the physical environment in all subjects. Thus, there was a decrease in the overall movement quality for movements made in the 2-D virtual environment. This suggests that 2-D video-capture virtual reality environments should be used with caution when the goal of the rehabilitation program is to improve the quality of movement patterns of the upper limb.
|
|
|
|
Liebermann, D. G., Krasovsky, T., & Berman, S. (2008). Planning maximally smooth hand movements constrained to nonplanar workspaces. J Mot Behav, 40(6), 516–531.
Abstract: The article characterizes hand paths and speed profiles for movements performed in a nonplanar, 2-dimensional workspace (a hemisphere of constant curvature). The authors assessed endpoint kinematics (i.e., paths and speeds) under the minimum-jerk model assumptions and calculated minimal amplitude paths (geodesics) and the corresponding speed profiles. The authors also calculated hand speeds using the 2/3 power law. They then compared modeled results with the empirical observations. In all, 10 participants moved their hands forward and backward from a common starting position toward 3 targets located within a hemispheric workspace of small or large curvature. Comparisons of modeled observed differences using 2-way RM-ANOVAs showed that movement direction had no clear influence on hand kinetics (p < .05). Workspace curvature affected the hand paths, which seldom followed geodesic lines. Constraining the paths to different curvatures did not affect the hand speed profiles. Minimum-jerk speed profiles closely matched the observations and were superior to those predicted by 2/3 power law (p < .001). The authors conclude that speed and path cannot be unambiguously linked under the minimum-jerk assumption when individuals move the hand in a nonplanar 2-dimensional workspace. In such a case, the hands do not follow geodesic paths, but they preserve the speed profile, regardless of the geometric features of the workspace.
|
|
|
|
Issurin, V. B., Liebermann, D. G., & Tenenbaum, G. (1994). Effect of vibratory stimulation training on maximal force and flexibility (Vol. 12).
Abstract: In this study, we investigated a new method of training for maximal strength and flexibility, which included exertion with superimposed vibration (vibratory stimulation, VS) on target muscles. Twenty-eight male athletes were divided into three groups, and trained three times a week for 3 weeks in one of the following conditions: (A) conventional exercises for strength of the arms and VS stretching exercises for the legs; (B) VS strength exercises for the arms and conventional stretching exercises for the legs; (C) irrelevant training (control group). The vibration was applied at 44 Hz while its amplitude was 3 mm. The effect of training was evaluated by means of isotonic maximal force, heel-to-heel length in the two-leg split across, and flex-and-reach test for body flexion. The VS strength training yielded an average increase in isotonic maximal strength of 49.8%, compared with an average gain of 16% with conventional training, while no gain was observed for the control group. The VS flexibility training resulted in an average gain in the legs split of 14.5 cm compared with 4.1 cm for the conventional training and 2 cm for the control groups, respectively. The ANOVA revealed significant pre-post training effects and an interaction between pre-post training and 'treatment' effects (P < 0.001) for the isotonic maximal force and both flexibility tests. It was concluded that superimposed vibrations applied for short periods allow for increased gains in maximal strength and flexibility.
|
|
|
|
Portnoy, S., Mimouni-Bloch, A., Rosenberg, L., Offek, H., Berman, T., Kochavi, M., et al. (2018). Graphical Product Quality and Muscle Activity in Children With Mild Disabilities Drawing on a Horizontally or Vertically Oriented Tablet. Am J Occup Ther, 72(6), 1–7.
Abstract: OBJECTIVE. We compared performance level and muscle activity patterns during shape copying and tracing in two positions, while sitting at a desk and while standing in front of a wall, between typically developing (TD) preschool children and children with mild disabilities (MD).
METHOD. Twenty-two TD children (8 boys, 14 girls; mean [M] age 5 5.2 yr, standard deviation [SD] 5 0.1) and 13 children with MD (9 boys, 4 girls; M age 5 4.9 yr, SD 5 0.5) participated in this study.
RESULTS. The children performed faster and smoother movements when copying shapes on the vertical surface, with no reduction of accuracy, than on the horizontal surface. Children with MD exerted their upper trapezius while performing the short tasks on the vertical surface compared with their muscle activity on the horizontal surface.
CONCLUSION. Incorporating short copying or drawing tasks on a vertical surface may increase the control of proximal muscles and ease graphomotor performance in children with MD.
|
|
|
|
Kaufman-Cohen, Y., Friedman, J., Levanon, Y., Jacobi, G., Doron, N., & Portnoy, S. (2018). Wrist Plane of Motion and Range During Daily Activities. Am J Occup Ther, 72(6), 1–10.
Abstract: OBJECTIVE. The dart-throwing motion (DTM) is a multiplane wrist motion that is needed for many daily occupations. Mobilization along the DTM plane may be essential for rehabilitation after wrist injury, but DTM angles are reported for the dominant hand alone, so their relevance to injury in the nondominant hand cannot be surmised. The aim of this study was to quantify the DTM plane angles for both hands during different activities of daily living (ADLs).
METHOD. Forty-three healthy participants wore a twin-axis electrogoniometer during ADLs.
RESULTS. No significant differences were found between the DTM plane angles of the dominant (20°�45°) and nondominant (15°�40°) hands. These angles varied by task and across participants.
CONCLUSION. The DTM plane is a functional motion used by both hands during ADLs. Because the DTM plane angle differs among hands, tasks, and individual clients, wrist rehabilitation involving the DTM plane should not be limited to a singular DTM plane angle.OBJECTIVE. The dart-throwing motion (DTM) is a multiplane wrist motion that is needed for many daily occupations. Mobilization along the DTM plane may be essential for rehabilitation after wrist injury, but DTM angles are reported for the dominant hand alone, so their relevance to injury in the nondominant hand cannot be surmised. The aim of this study was to quantify the DTM plane angles for both hands during different activities of daily living (ADLs).
METHOD. Forty-three healthy participants wore a twin-axis electrogoniometer during ADLs.
RESULTS. No significant differences were found between the DTM plane angles of the dominant (20°�45°) and nondominant (15°�40°) hands. These angles varied by task and across participants.
CONCLUSION. The DTM plane is a functional motion used by both hands during ADLs. Because the DTM plane angle differs among hands, tasks, and individual clients, wrist rehabilitation involving the DTM plane should not be limited to a singular DTM plane angle.
|
|
